Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Spring Replacement Cost in Spring?
Spring replacement in Spring, TX typically costs $180 – $340 per spring, and most doors have two springs that are replaced as a matched pair at roughly double that cost. That figure covers the spring, the labor to remove the door’s stored tension safely, and balancing afterward. A written estimate is what sets your final price, so the range you see here is a planning number, not a quote.
If your door is stuck open or closed and you’re in Spring, call (855) 337-1360. Estimates are free, and we work with same-day service and fast dispatch from 7am to 7pm.
Key Takeaways
- One spring: $180 – $340. Matched pair: about $360 – $680.
- Torsion and extension springs are the only focus of our spring service, not an add-on to general handyman work.
- A snapped spring means the door should not be used until it’s fixed – the opener and cables take the load instead of the spring, and that’s when secondary damage starts.
- Our technicians have up to 10 years of experience, and we know the spring setups on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor doors.
Spring Replacement Cost Breakdown (2026)
Here’s how the numbers break down by the type of work involved. These are typical estimated ranges for the Spring market, and the written estimate you get sets the final price.
| Item | Typical Cost (Spring, TX) |
|---|---|
| Single torsion spring replacement | $180 – $340 |
| Matched pair of torsion springs | About $360 – $680 |
| Single extension spring replacement | $180 – $340 |
| Matched pair of extension springs | About $360 – $680 |
| Garage door spring repair (general repair range) | $180 – $340 |
| Cable repair (often needed after a spring failure) | $130 – $250 |
| Roller replacement (done alongside a spring job) | $110 – $220 |
| Track realignment | $120 – $240 |
| Opener repair (spring failure can strain the opener) | $120 – $320 |
| Opener installation (if the unit was damaged) | $250 – $550 |
| Garage door repair (broader range for combined issues) | $150 – $600 |
One spring or a pair? We do the work at the pair price because matched springs are made to share the load. Replacing one spring on a door built for two means the old spring carries more than it was designed for, and it usually fails soon after. The pair is almost always the better call on any door that’s already had one spring go.
What pushes a job toward the top of the range? Heavy doors. High-cycle use, like a door that opens and closes many times a day. Springs that have already failed and left the door sitting at a bad angle. Cables that are frayed or kinked. Track that bent when the door dropped. Those extras add to the ticket, and it’s why we look at the whole spring system before we quote, not just the broken part.
What keeps a job near the bottom? A standard-width single-car door, springs that fail cleanly with no secondary damage, and rollers and cables in decent shape. In a lot of Houston-area homes that’s the straightforward case.
If the door also has opener trouble – a LiftMaster, Chamberlain, or Craftsman unit that’s adding a grinding sound on top of the spring issue – that’s a separate line item. We handle opener repair too, so the door and its drive system get looked at in one visit. For more on the full repair range, see our Spring Garage Door Repair Pros page.
What Affects Spring Replacement Pricing in Spring
- How many springs the door uses. Almost every residential door built for a two-spring setup should get both replaced, and a matched pair costs about twice a single spring. A one-spring door keeps the job simple.
- Torsion vs. extension springs. Torsion springs sit on a shaft above the door and take more careful tensioning; extension springs run along the sides. Both land in the same range, but torsion setups on wider, heavier doors can call for stronger springs and more time.
- Door weight and width. A double-wide Clopay or Amarr door with a heavier panel package needs springs sized for it. Spring caliber matters – the larger the wire gauge, the more the part costs, and the more care it takes to install.
- Secondary damage. When a spring snaps, the door drops or stalls and can bend a track or strain a cable. Track realignment and cable repair get added to the ticket, and if the opener ran against a dead door, that may need attention too.
- Spring cycle life. A standard spring and a higher-cycle spring both fit your door, but they’re priced differently. If your door gets used a lot – family coming and going all day – a higher-cycle spring can make sense. We’ll lay out the options and let you choose.
- Access and working conditions. Tight side clearance, a low ceiling, or a door partially stuck in a bad position can add time to the job. We want a clear, safe setup, and the estimate reflects what we find.
Spring, TX homes sit in a warm, humid climate with mild winters. Heat and humidity are hard on metal over the long haul – springs are steel under constant load, and garage interiors run hot in our summers. That’s a general reality of the market, not a reason to panic. It does mean that when one spring fails, the other has lived the same life, which is another argument for replacing the pair.
How to Save on Spring Replacement
Springs are a safety-critical component, so the savings come from making smart choices, not from cutting corners. Here’s how to keep the job reasonable.
- Replace the pair, not the single. Doing both springs at once avoids a second labor charge when the other one goes – and on a two-spring door, it will go.
- Combine work on the same visit. If the rollers are worn or a cable is frayed, replace them while we’re already on the door. A combined visit costs less than two separate calls.
- Get a written estimate up front. Estimates are free. Ask for the price in writing before any work starts so there are no surprises.
- Fix the door, but skip the upsell. If the door is fine and only the springs failed, you don’t need a new opener or new panels. A specialist should tell you that plainly.
- Don’t run the door on a failed spring. Every cycle on a dead spring puts the load on the opener and cables. Catching it early keeps the bill in the spring-only range instead of pulling in opener repair and cable repair.
Call (855) 337-1360 for a free estimate. Upfront pricing, same-day service where we can make it work, and a satisfaction guarantee to back the work.
FAQs – Spring Replacement Cost
How much does it cost to replace a garage door spring in Spring, TX?
$180 – $340 for one spring, and about $360 – $680 for a matched pair, which is what most doors need. The exact price depends on the spring type, door size, and whether anything else got damaged when the spring let go. Call (855) 337-1360 for a free estimate – it’s the only way to get an exact number.
Is it cheaper to repair or replace the garage door springs?
Repair is the cheaper path in almost every case, and it’s the only safe one. A full spring replacement runs $180 – $340 per spring, far below new door installation, so replacing a working door just because a spring failed doesn’t make sense. If the panels, tracks, and opener are sound, the springs are the fix. We’ll tell you honestly if the door is past saving. Call for a free estimate and we’ll walk through it.
Can you come out today for a broken spring in Spring?
Often yes – same-day service is the goal, with fast dispatch from 7am to 7pm. A snapped spring is the most common garage door failure and we treat it as urgent. We can’t promise a specific time until you call, so phone (855) 337-1360 and we’ll book you in. Estimates are free.
Do I need to replace both springs at the same time?
On a two-spring door, yes – plan on roughly double the single-spring price, $360 – $680 for the pair. Matched springs share the load, and a fresh one paired with a worn one usually fails sooner. Replacing the pair now beats two separate visits. Call (855) 337-1360 to get a pair priced for your door.
Can I replace my own garage door springs?
No – this is one job to leave to a trained technician. A torsion spring holds the full weight of the door under high tension, and the winding process can cause serious injury if something slips. We handle the tension, the cables, and the balancing. It’s not worth the risk. If a spring has failed, keep the door closed and call (855) 337-1360 for a free estimate.
Why a Spring Specialist Makes Sense on a Spring Job
General contractors and handyman services often take garage door work on the side, and a lot of doors get installed or repaired by people whose main trade is something else. Spring work is different. It’s calibrated tension handling, and it’s genuinely dangerous without the right training and the right tools. That’s why we do spring replacement as our core service rather than a sideline.
We service and install products from eight of the most widely-owned garage door and opener brands: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That means whether you’ve got a Clopay panel door or an Amarr steel model, the springs and hardware match the door. For opener repair the major names are LiftMaster, Chamberlain, Genie, and Craftsman, and we handle those too.
Brand-fluent, niche-focused, and specific about what we do. If you want a generalist who touches every trade, we’re not that. If you want the door handled correctly, we are. The local technician who comes out is licensed and insured as their state requires.
What to Do When a Spring Breaks in Spring, TX
First, don’t force the door. Leave it closed if it’s down, or propped safely if it’s up, and keep the opener off. Call us and we’ll book an appointment and explain what to expect. You don’t need to diagnose anything; the technician will check both springs, the cables, the track, and the opener in one visit.
When we arrive, expect a look at the whole system, a clear explanation of what failed and why, and a written price before any work starts. Spring work is $180 – $340 per spring, so a paired repair is rarely a shock once it’s laid out. We work with same-day service and fast dispatch from 7am to 7pm, and estimates are free.
Why Choose Spring Garage Door Repair Pros
We’re a garage-door-only service company, which means our diagnostic accuracy comes from doing one thing and doing it well. Springs are the mechanical heart of the door, and we know the brands cold – from a LiftMaster opener to a Raynor door to a Craftsman opener from an older install. If you need a part, we can supply it rather than parceling out the job to a third-party vendor. From a snapped spring to a full new install, one call covers it. Our technicians have up to 10 years of experience, and they treat spring failure as what it is: the most common, most mechanically critical problem a door has.
Our focus stays on garage doors. We repair doors, repair and install openers, supply replacement parts, and handle full new door and opener installations. When the spring is the issue, we handle it correctly the first time.
Get a Free Estimate on Spring Replacement in Spring Today
Spring replacement in Spring, TX runs $180 – $340 per spring, or about $360 – $680 for a matched pair, and a free estimate gives you the exact number for your door. Call (855) 337-1360 to book same-day service and upfront pricing. Dispatch runs 7am to 7pm, and every job is backed by a satisfaction guarantee. A snapped spring doesn’t wait, and neither should you.
Written by the team at Spring Garage Door Repair Pros. Pricing reflects the Spring market as of 2026. Spring Garage Door Repair Pros offers free estimates – call (855) 337-1360.
What Our Customers Say
"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Emily Pruitt"Opener works, remotes are programmed, no complaints on the work. Took three days to get on the schedule though, so if you've got a car trapped inside, say so when you call."
- Mark Meyer"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."
- Gabriela Morales